Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the eggs to heat or cool more than it should. The amount this happens will depend on the amount of heat your heating element holds and the amount of circulation in your incubator. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. Note: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds) For example, if you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) This means that you can calibrate the thermostat if required. This means that if the temperature is set to 99.5 then the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7Ĭalibration enabled. The temperature switching differential is 0.2 degrees F. The digital readout displays temperature to the tenth of a degree (98.7, 99.4) Set point can be adjusted to any temperature between 41-113 degrees F Comes preset to 99.5 degrees F (37.5 in Celsius mode). The white thermostat may be mounted on the outside of the incubator. This unit comes with a 24 inch remote sensor that can be placed inside your incubator. The screen has a flame icon that turns on when the heater is operating. Just press the up or down arrow to set it. The temperature can be adjusted in 0.1 degree increments. Simply plug in your heater, heat mat, or light bulb to the 3 outlet plug outlet and you’re ready to go. You can use any heating element up to 225 Watts. It's great for both tabletop and cabinet incubators. The Plug ‘n Play is a digital electronic thermostat with remote sensor designed specifically for incubators. When incubating eggs, accuracy counts! That is why a proportional style thermostat is preferred. This allows the temperature swing to be much less than the on/off style thermostat. Then it will increase the power as the temperature starts falling away from the set-point. It will reduce the amount of power going to the heater as the temperature gets close to the set-point. The proportional style thermostat adjusts the power up and down as the temperature starts getting close to the set-point (your target temperature). This style creates a wider swing in temperature because the temperature has to get too high or low before the thermostat responds. Then it turns it completely off when the temperature gets too high. What is the difference between a proportional thermostat and an on/off thermostat?Īn off/off style thermostat turns the heater on full power when the temperature gets too low. See this video to see how easy it is to install the Incubator Control Module: Feel free to contact us if you would like further clarifications about this option. Then when the heater that you are regulating with the thermostat is on, you will have enough power in your incubator. For example, if you think you will need about 350 watts for your incubator, you can put a 60 watt light bulb inside the incubator that is always on. NOTE: if your incubator needs more power than 300 watts, you have the option of using a heater that is always on in order to bump up the entire wattage inside the incubator. Key features- Proportional thermostat - minimizes temperature swings (see details below)- Comes pre-set to 99.5 degrees F (easily adjustable, if desired)- Electronically controlled - Digital display- Controls the heater, fan and egg turner motors (it is not required to use this module to control all accessories, if you desire not to)- Hatch timer- Thermostat is calibration enabled- 110/120v power input - Remote sensor for accurate temperature reading- Easily mounts into your incubator (see video below)- Maximum heater wattage: 300 watts (see note below if you need more power) This is designed to control the temperature, air circulation and automatic turner motors in your incubator. This device lets you add a sophisticated control module to your cabinet (or larger-style) egg incubator.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |